4 Ton Heat Pump

Unit&Installation Costs: 6500$
Running(a month) Costs: 200$
Service(a year) Costs: 160$
Replacement Costs: 400$

A four ton heat pump system gives you a wide area of coverage, and serves as both an air conditioning and a furnace system at once. During winter months, you can easily allow warm air to be pushed into the building with the use of a heat pump


Unit&Installation Costs

4 ton Heat pump cost are $4000 to $8,500 for the equipment and installation labor on average. *Average home uses a 3 to 4 ton unit. Heat pump size needed also depends on climate zone.


Running Costs

If run all the time, Average 4 ton will cost around $0.67 to run a hour, $16.08 per day, $482.40 per Month – consuming between 1,000 and2,000 kilowatt hours of electricity.


Service Costs

Generally, getting your air source heat pump serviced will cost you between $150-200. However, this price can fluctuate, depending on the company you go with and the size of your heat pump. Heat pump maintenance actually costs considerably less compared to traditional gas- or oil-fuelled boilers


Replacement Cost

Receive up to $4,000 to replace or repair 4 ton heat pump. Systems must be at least 20 years old. Receive up to $1000/ton of heat pump when replacing an existing 4 ton heat pump system.


Is it Worth?

Four-ton heat pumps are designed to keep larger spaces comfortable. Most can easily cover areas as large as 2,000 square feet. Just like with any other size of heat pump, you must ensure that a four-ton heat pump is right for your space before investing in one. If the unit is too large for your home, it will short cycle and possibly damage the motor.

In this article, I will go over the square footage and amperage requirements for a 4-ton heat pump for a mobile home. It will also help you decide which unit would be the right choice for your home. This article will also cover the question, “Is a 4-Ton Heat Pump Good Enough?”

4-ton heat pump square footage

When you install a heat pump in your home, you must follow certain rules to achieve maximum performance and efficiency. As a general rule, you should choose a model with at least 16 SEER rating. The government recommends that a heat pump should have at least 14 SEER, but some manufacturers recommend that you install a higher-rated model. A 4-ton heat pump should be adequate for a two-thousand-square-foot home if it includes proper insulation, doors, and windows.

The capacity of the heat pump is measured in British Thermal Units (BTUs) per ton. A four-ton heat pump produces 48,000 BTUs of heat or cold per hour, which is equivalent to 2,000 square feet.

4-ton heat pump for mobile home

When it comes to choosing a high-quality 4 ton heat pump for your home, the best option is to purchase it from a manufacturer. Manufacturers are much better at ensuring that their products are of high quality. Additionally, manufacturers perform quality control more carefully than retailers and installers. This means that the heat pump will run at peak efficiency. Some manufacturers also offer heat pump ready options, such as those with an eight-wire thermostat control cable and a multi-speed air handler motor. The factory-installed heat pump should be easier to install, eliminating a number of potential problems.

You may want to consider installing better insulation if you have an older mobile home. This will increase the efficiency of your heat pump and reduce your operating costs. Older mobile homes tend to have less insulation than newer models, so proper insulation will help your mobile home stay warm in the winter and cool in the summer. Additionally, you can install a programmable thermostat to increase your heat pump’s efficiency. It will automatically adjust temperature according to the climate outside, which will save you money on your heating bill every year.

4-ton heat pump amperage

There are a few things to keep in mind when selecting a heat pump. Heat pumps draw a certain amount of electricity. In fact, they might even draw more than a standard heater. However, the amount of money you can save on energy costs will depend on your home, the size of your pump, and the way in which you control its operation. Homeowners can use online tools to calculate their potential energy savings, such as NRCan’s ASHP-Eval. They’re free and can be used by installers and mechanical designers.

Single-phase heat pump manufacturers recommend using a circuit breaker sized at 125% of FLA, but that size won’t hold the starting load. You should instead purchase a type HACR breaker, which can handle this kind of load. Another option is to use a Fusetron type breaker. These are similar to the Fusetron fuses, but are typically used for motor loads. If your heat pump requires a higher amount of power, you can use a 175%-rated breaker.

4 ton heat pump brand 2022

Goodman 4 Ton 16 Seer Heat Pump GSZ160481

unit costs: $3,050

Goodman 4 Ton 16 Seer Heat Pump GSZ160481
BrandGoodman
Special FeatureDefrost
Seasonal Energy Efficiency Ratio (SEER)16
Power SourceGas Powered
Model NameGSZ160481
Control MethodApp

Trane 4 Ton 16 SEER Single Stage Heat Pump System Includes Installation
Install cost: $7,840.00

Trane 4 Ton 16 SEER Heat Pump System
Nominal Capacity4 Tons
Stages1
SEER Rating16.5 SEER
EER Rating13 EER
HSPF9
Capacity48000 BTU
Heat Pump unitTrane 4TWR6048H1000A
Indoor Air Handler unitTrane TEM6A0C48H41SB*
Electric Heater unitTrane BAYHTR1517BRKA

4 Ton Rheem 14 SEER R410A Heat Pump Split System
Unit cost: $3,903

Model Number: RP1448AJ1NA, RH1T4821STANJA

4 Ton Rheem 14 SEER R410A Heat Pump Split System

Features
• 10-year warranty on parts and compressor
•  Scroll compressor uses fewer moving parts for higher efficiency & increased reliability
•  Quiet and efficient constant torque ECM indoor blower motor
• Four-way design for upflow, downflow, horizontal left and horizontal right installations
•  Composite condenser base pan eliminates corrosion & reduces decibel levels
•  All aluminum factory-installed evaporator coil
•  Insulated air handler blower compartment optimizes thermal and sound performance
•  Corrosion resistant condensate air handler drain pan
•  Factory installed expansion valve for indoor coil
•  Improved condenser coil design reduces vibration & stress minimizing leaks
•  Condenser pre-charged with R410A refrigerant
•  Filter drier included (field installation required)
•  Enhanced mufflers help lower vibration energy for quieter operation
•  Suitable for use in mobile homes

Specifications
Condenser Dimensions:  H35″ x W33 3/4″ x D33 3/4″
Air Handler Dimensions:  H50 1/2″ x W21″ x D21 11/16″
Volts:  208/240
Phase:  1
Hertz: 60
EER:  11.0
HSPF:  8.2
Liquid Line Valve Connection:  3/8″ outside diameter
Suction Line Valve Connection:  7/8″ outside diameter

Do you wish to get the latest heat pump news, technology, markets, and discounts? Subscribe Now!
0
Would love your thoughts, please comment.x
()
x